Default PLN pricelist
  1. All Products
  2. VOLTAGE/ CURRENT
  3. PM06D Power Module (14S)

PM06D Power Module (14S)

https://www.bzbuas.com/web/image/product.template/498/image_1920?unique=adffbdc
The PM06D Power Module is a reliable and efficient solution for powering your Pixhawk® 5X & 6X flight controllers. It offers a regulated power supply for your Pixhawk from a 2S to 14S LiPo battery, as well as the ability to monitor current consumption and battery voltage. This versatile module comes equipped with a built-in power distribution feature, allowing you to power your Electronic Speed Controllers (ESCs) and Flight Controller (FC) from the same board.
159.00 zł 159.0 PLN 159.00 zł z VAT 
129.27 zł z VAT 
Contact to order

This combination does not exist.

Contact Us

Regulamin
 Wysyłka w ciągu 2-3 dni roboczych

Moduł zasilania PM06D (14S) żeby prąd płynął regularnie

PM06D is supported by PX4. For Ardupilot, it is supported in version 4.4 and later.

This PM uses I2C digital signal data output and is not compatible with a flight controller that uses analog PM such as the Pixhawk 6C & Mini, Pixhawk4 & Mini, pix32 v5, or Durandal flight controllers.


Moduł zasilania PM06D (14S) integralny z CubePilot i Ardupilotem

PM06D Power Module provides a regulated power supply for your Pixhawk® 5X & 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6-pin cable. It has built-in power distribution, allowing you to power your ESC and FC with the same board.

The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 14S. The Power Module comes completely assembled with an XT60 connector and a capacitor. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact.


WŁAŚCIWOŚCI Moduł zasilania PM06D (14S)

The PM06D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute). If a higher current is needed, the plug type and wire size should be changed accordingly. You can refer to this chart as a reference.


Typ złącza

Przekrój przewodu

Prąd ciągły (4 godziny, wzrost temperatury < 60 °C)

Prąd chwilowy (1 minuta, wzrost temperatury < 60 °C)

XT60

12 AWG

30 A

60 A

XT90

10 AWG

45 A

90 A

XT120

8 AWG

60 A

120 A

AS150

8 AWG

75 A

150 A

AS300

6 AWG

150 A

300 A


PX4 PARAMETER SETUP:

  • If you are using the PM06D 14S version, you must set SENS_EN_INA228 to enable.


Moduł-zasilania-PM06D-(14S)

Moduł-zasilania-PM06D-(14S)


SPECYFIKACJA Moduł zasilania PM06D (14S)

  • Input voltage: 2S- 14S
  • PCB Cont. Current Rating: 70A
  • PCB Burst Current Rating: 120A (<60 Sec)
  • Max current sensing: 327A
  • Voltage and current monitor with I2C compatible interface
  • Connector Outputs: 5.2V and 3A max
  • Otwory montażowe: 30.5mm*30.5mm
  • Wymiary: 35x35x5mm
  • Masa: 24,5 g

 

ZESTAW Moduł zasilania PM06D (14S) ZAWIERA

  • 1x PM06D Power Module
  • 1x kabel JST-GH 6-pinowy o długości 150mm